The ABM C115-500 EVO III combo combines the features of the ABM 500 EVO III head with a single 15" Ashdown BlueLine driver in a precision tuned cabinet. The cabinet is constructed from high-grade birch ply with properly screwed and glued joints, protected by a tough, buffalo leather cloth covering and chromed metal corners. All amplifier chassis are built from heavy-duty 16 swg zinc coated mild steel, foil lined to minimise interference, and special Ashdown-designed metal handles are used in favour of inferior flip handles which can rattle after years of use.
The ABM 500 EVO III is a 575 watts RMS bass amp head designed to satisfy both bass-purists and tech-heads alike. Three straightforward rotary tone controls provide 20dB of cut and boost at 60Hz, 660Hz and 5kHz, and are supplemented by two pairs of additional sliders giving 15dB cut and boost at 180Hz, 340Hz, 1.3kHz and 2.6kHz. The EQ can be switched in/out by a footswitch, enabling players to go from a flat fretless sound to a boosted sound via a favourite EQ setting. A single input is switchable for passive and active instruments with a blend of solid state and dual triode tube preamps stages which can be preset and selected by footswitch, providing access to a massive range of clean, warm and overdriven tones.
Also footswitchable is the on-board compressor and the mighty Ashdown sub-harmonic generator which precisely tracks the main signal and reproduces it an octave lower. A sub-harmonic level control enables the player to add just the right amount of low-end reinforcement - everything from a subtle, thickening of the sound to unbridled, bone crushing tone. The ABM 500 EVO III features a front-panel mounted balanced DI out with pre or post EQ switching, a sub-bass output, a tuner output, an FX loop and a line input for the connection of an external sampler or sound source. Output muting cuts the signal from the DI output but leaves the tuner output 'live', allowing the player to tune up in silence. A new upgraded power section has faster transient attack, more headroom and even less noise.
Ashdown BlueLine speakers are specially developed to achieve a superb balance of power, transparency and deep, controlled low end, without sacrificing any of the mid-band attack and high-end brightness that are so important in a modern bass sound.
|Power Requirement:||230 /115v|
|Speaker Configuration:||1 x 15" BlueLine Bass Driver|
|Frequency Response:||-3dB at 17Hz and 30KHz|
|Speaker Outputs:||Minimum impedance 4 Ohms|
|High Instrument Input:||Impedance 3.9MOhms / Input range 150mV - 20V p-p|
|Low Instrument Input:||Impedance 10KOhms / Input range 300mV - 40V p-p|
|Line Input:||Impedance 22k Ohms / Input level 0dBu nominal|
|Sub Output:||Impedance 1K Ohms, level 0dBu nominal|
|DI Output:||600 Ohms balanced / Level -20dBu nominal|
|Tuner Output:||Impedance 22k Ohms / Level 0dBu nominal|
||Bass +/-15dB @ 45Hz|
Middle +/-15dB @ 660Hz
Treble +/-15dB @ 7kHz shelving
Slider 1 +/-15dB @ 180Hz
Slider 2 +/-15dB @ 340Hz
Slider 3 +/-15dB @ 1.3kHz
Slider 4 +/-15dB @ 2.6kHz
Shape (Push Flat) +8dB @ 50Hz & 4kHz, -8dB @ 400Hz, filter slope - 6dB/octave
|Effects Send:||Impedance 22k Ohms, Level 0dBu nominal|
|Effects Return:||Impedance 22k Ohms, input level 0dBu nominal|
|H x W x D (mm):||587 x 610 x 335|